TEL: +86 18320188145 丨 Whatsapp:+86 13909754659 
How To Make The Acid-Alkali Resistant Chemical Pump Have a Lo
TIME：2025-02-17 Author：admin Views：
How To Make The Acid-Alkali Resistant Chemical Pump Have a Longer Service Life
The acid-alkali resistant chemical pump is mainly used for the use of various kinds of liquid medicines. It is different from the clean water pump, but it is also a consumable. An acid-alkali resistant chemical pump cannot be used for a lifetime, because in the process of use, due to the effect of cooperation with liquid medicines, the corrosiveness of liquid medicines, or improper use, the service life of the chemical pump will be reduced. Although we cannot make an acid-alkali resistant chemical pump permanent, we can also use some methods to make it last longer. Just like a car, people who love cars can drive it for twenty years, while people who don’t know how to cherish it may not drive it for more than ten years. The same is true for acid-alkali resistant pumps. Now let’s take a look at how to make the chemical pumps in our hands last longer.
The acid-alkali resistant chemical pump is mainly used for the use of various kinds of liquid medicines. It is different from the clean water pump, but it is also a consumable. An acid-alkali resistant chemical pump cannot be used for a lifetime, because in the process of use, due to the effect of cooperation with liquid medicines, the corrosiveness of liquid medicines, or improper use, the service life of the chemical pump will be reduced. Although we cannot make an acid-alkali resistant chemical pump permanent, we can also use some methods to make it last longer. Just like a car, people who love cars can drive it for twenty years, while people who don’t know how to cherish it may not drive it for more than ten years. The same is true for acid-alkali resistant pumps. Now let’s take a look at how to make the chemical pumps in our hands last longer.
Acid-alkali resistant chemical pumps
Before starting, some necessary inspections should be done: whether the rolling condition of the pump shaft is normal, whether there is any stuck phenomenon: whether the position of the impeller is normal: whether the cable and cable plug are broken, scratched and broken, etc. During operation, pay attention to the change of voltage, which is generally controlled within the +5% range of the rated voltage. In addition, the position of the chemical pump in the potion is very important. It should be selected in a place with sufficient water and no impurities as much as possible, and it should be suspended vertically in the potion. It is not allowed to be placed horizontally to avoid falling into the mud or being blocked by suspended matter, which will cause a sharp drop in water output or even failure to pump the potion.
Self-priming pumps
It should be placed in a well-ventilated place as much as possible to run, so as to facilitate rapid heat dissipation and reduce the temperature of the motor. Otherwise, long-term operation will easily burn the motor. For example, when a farmer used a self-priming pump, he did not remove the plastic film covering the motor, causing the motor to overheat and burn the coil. In addition, before starting, be sure to check the amount of water stored in the pump body, otherwise, it will not only affect the self-priming function, but also easily burn the shaft seal components. Under normal circumstances, the chemical pump should discharge water 3 to 5 minutes after starting, otherwise it should be stopped immediately for inspection.
Repair of acid and alkali resistant chemical pumps
Once there is a problem with the acid and alkali resistant chemical pump, do not disassemble it yourself. When you disassemble it yourself, you don't know where the problem is and disassemble it blindly; secondly, you don't have special tools and often damage the original intact parts. The best way is to go to an experienced and planned repair station for repair, and replace "overage" parts and certain wearing parts in time. Under normal circumstances, the chemical pump should be repaired every six months.
If you have any technical or product details you would like to consult, please contact our salesperson and we will do our best to answer your questions.
WhatsApp:
+86 13909754659
Email:
kelseyluweilai@gmail.com
weilaihbsb@163.com
If you have any technical or product details you would like to consult, please contact our salesperson and we will do our best to answer your questions.
WhatsApp:
+86 13909754659
Email:
kelseyluweilai@gmail.com
weilaihbsb@163.com
-THE END-
